Thursday, February 28, 2013

EasiFix: Masters of the Universe - The legs!

One of the most dreaded moments of MOTU collectors is that broken rubber band sight. One day fine looking on the shelf, next day fallen figure.

Sometimes, even inside the mint card. Well, nothing we can do about the latter. However, the former is fixable.


Let´s get them back on their feet again!


Material. A pair of pliers, a curved punch tool (a thin screwdriver will do), a thin electrical cable and the main characters, 2 O-rings and 2 eye screws.


Sometimes (more than often in my case) figures come to your hands with former attemps from other collectors (or previous owners). I´ve seen a lot of hot glue techniques. While it´s usually a weak solution, it´s fast and doesn´t leave marks.


For those who don´t know where that comes from, here´s the crook.


But let´s do this the way it´s supposed to be done, shall we?


First, remove whatever may be inside the crotch. Pictured, the original rubber band. Dried, broken.


Where we´re going to work. Not the bigger space.


Remove the rest of the broken rubber. The original ends will remain. You´ll need them too.


This is how small (or large) your eye screw needs to be.


Same goes for the O-rings. The smaller, the better. However, the smaller they are, the more difficult to work with. Keep that in mind.


Pick up your pair of pliers and go ahead and open up one eye screw and put the 2 O-rings inside.


Screw it (clockwise) to one of the leg´s remain of original broken rubber band. This is one of the good things about this process. You´re not doing any harm to the original parts. If you do it the right way. Meaning stop when the eye screw reaches the PVC leg.


Like so.


Now pick up your wire and put it through the O-rings. This is why I choose the electrical wiring. Because of the plastic insulation. So you won´t harm neither the figure or the rubber O-ring.


Also, because you can mold it to easily pass where it needs to go. So as you can see and as I told you previously, you need to pass it through the top opening. NOT the larger one.


So now we need to pull the leg to its place.


Some rubbers are of better quality than others (kinky). So, while most handle the job perfectly, others tend to break right about here. Because in order to keep the legs nice and tight, you need to pull to have space to work with the other leg.


Now you need to insert the punching tool, needle, screwdriver, whatever you prefer to work with here. Be careful not to harm the plastic. This is why you should use an under C-8 figure to master the process. Not a big deal, but the more you do, the better you get.

 
Now you can remove the wire and forget about it.


Open another screw and prepare to the final step.


Close it.


Before removing the tool you inserted to prevent the "new" rubber band to escape, take a few (clockwise) turns to get half the job (well) done. Then remove the needle, while holding the eye screw and pulling the "double O-ring band" and screw the best you can to be nice and tight.


And you did it!


Back in action!!!



Evil Snake Men creature with the quick-strike head... fully restored.

Thank you for reading and happy fixes!










Tuesday, February 26, 2013

Masters of the Universe Clamp Champ - Vintage

 One of the very final figures to be release, the powerful Heroic Warrior wields his tremendous Clamp weapon to grab Eternia´s enemies. Here presented, the European version!


Now what makes this one different from the only black figure in the line? A harder head, no eyelashes and softer plastic arms are the obvious.


Featuring a 1981 Spanish body mold.


Eternian Games title gave him the opportunity into the Royal services and a job as King Randor´s bodyguard.


Amazing figure, Clamp Champ was supposed to get a 2002 release before the show´s cancellation.


Figure: Clamp Champ, Mattel 1986 (here presented, the European version)


Armor is a repaint of Fisto´s.


Weapon: Clamp. A little hard to grab, despite Clamp Champ´s notable strenght, the best way to hold it is to insert the thumb into the handle´s opening.


Push the trigger and weapon closes on the minions!


"Where are YOU going?".


Introducing Eternia´s new Champion: Clamp Champ!


At the very end of this review, the rubber broke. ARGHHH. Well, a golden opportunity to leave open the future small tutorial on how to solve it. Stay tuned! And thanks for visiting!

Status: Unavailable

Wednesday, February 13, 2013

Adventure Heroes Giant Crawler Playset - Cobra - UPDATED!

Another retired 2007 set, King Tutenskull here present with a giant Cobra snake.


This was for many, one of the best sets ever distributed. The over-sized cobra not only works alone, but stands as the best "Golobulus" custom possibility ever.


MIB, Chap Mei, 2007.


Included accessories. Most staffs came bent. No worries, just get some really hot water, dip, straight and put in the freezer for a while.


Giant creature - the King Cobra.


Amazing (giant) animal for your 1:18 scale... or whatever purpose you may find.    


Figure: King Tutenskull.


The legs don´t move, but since this was basically a figure to change form with the snake, it´s understandable, but from the action figure articulation point of view, this is probably one of the weakest Chap Mei examples. The sculpting is very good, on the positive side. Removable king´s "clothing" accessory.


Set can be split into 4 pieces. Interchangeable.


Pressing the snake´s nape, the jaw will move up.


King Tutenskull in a Mortal Kombat style!


Uh... no.


Cobra´s head is very similar to the original CM Cobra from Wild Quest, but scultping on a more fantasy level is superior. 

Status: Unavailable